Pass HPE7-A06 Exam – Real Test Engine PDF with 128 Questions [Q53-Q69]

By adminOn May 19, 2026

Rate this post

Pass HPE7-A06 Exam – Real Test Engine PDF with 128 Questions

Get New HPE7-A06 Certification Practice Test Questions Exam Dumps

Q53. Which settings should be checked first when troubleshooting an HPE switch stack with inter- switch latency?

Stack cable connections

Spanning tree configuration

MTU configuration

Stack firmware versions

Q54. What is the best practice for using Dynamic Segmentation?

Use UBT to create isolated networks foe specific typos of devices.

Use a combination of role-based access and overlay technologies to create a layered security approach.

Use Dynamic Segmentation only on devices thatare connected to the network via Wi-Fi.

Use LUR to assign roles to devices based on their location and DUR to assign roles to devices based on their user identity.

Q55. A client is unable to connect to the network. In the HPE Aruba Networking ClearPass access tracker, we can see an EAP timeout. What is a possible cause of this message?

The radius server does not trust the client certificate.

The radius server can see that the client certificate is expired.

The client can see that the radius server certificate is expired.

The client does not trust the radius server certificate.

Q56. Review the diagram and existing configuration of RouterA above. Which configuration changes are necessary to permit load balancing between RouterA and RouterB? (Selecttwo) Exhibit.

Q57. Drag and Drop Question
Match the customer requirement with commands used to partially configure the network technology used to fulfill the requirement.

Q58. To ensure device redundancy in an HPE Campus Access network, which configurations should be applied?

Link Aggregation

Active-Active Failover

DHCP Snooping

VRRP

Q59. A customer hassot a requirement for VLAN 151 to be an isolated VLAN. A colleague has copied and pasted a partialconfiguration, but you do not achieve the desired outcome. This is the code that was added:
What should be added to the configuration before this code to achieve the desired result?

The customer requires VLAN 151 to be configured as an isolated Private VLAN. A partial configuration was added, but the desired outcome wasn’t achieved. We need to determine which configuration snippet should be addedbeforethe (unspecified) partial configuration to correctly set up the Private VLAN structure.
* Private VLAN Configuration Fundamentals:
* APrimary VLANmust be defined. This VLAN carries traffic between promiscuous ports and ports in associated secondary VLANs.
* Secondary VLANs(either isolated or community) are associated with the primary VLAN.
* Ports are then mapped to either the primary VLAN (promiscuous ports, typically router/firewall connections) or a secondary VLAN (host ports). Isolated ports within thesameisolated VLAN cannot communicate with each other.
* Analyzing the Options (Assuming VLAN 15 is the intended Primary):
* A)
vlan 15
private-vlan primary
vsx-sync
This correctly defines VLAN 15 as the Primary Private VLAN. The vsx-sync command ensures this configuration is synchronized across a VSX pair (relevant if applicable). This is the necessary prerequisite before defining VLAN 151 as an isolated secondary VLAN and associating it with VLAN 15.
* B)isolated-vlan primary is incorrect syntax. The command is private-vlan primary.
* C)primary-vlan isolated 151 is incorrect syntax for defining either the primary or secondary VLAN type/association within the primary VLAN context.
* D)private-vlan isolated 151 within the vlan 15 context is incorrect syntax. The private-vlan isolated command belongs under the configuration of the secondary VLAN (VLAN 151 in this case).
* Conclusion:Before configuring VLAN 151 as private-vlan isolated and associating it, the primary VLAN must be defined. Option A correctly shows the command (private-vlan primary) under the intended primary VLAN’s configuration (vlan 15) to establish it as the primary VLAN.
References:AOS-CX Security Guide (Private VLAN configuration steps and commands). This relates to the
“Switching” (19%) and “Security” (10%) objectives.

Q60. Drag and Drop Question
Place the steps in sequence.
What is the order of the recommended steps to troubleshoot an issue?

Q61. Refer to the exhibit.

What needs to be defined on Edge-1 to establish valid BGP routing between agg-sw1 and agg- sw2 using BGP protocol using the IP addresses described in the image above?

Q62. What is the best practice for using Dynamic Segmentation?

Use UBT to create isolated networks for specific types of devices.

Use Dynamic Segmentation only on devices that are connected to the network via Wi-Fi.

Use LUR to assign roles to devices based on their location and DUR to assign roles to devices based on their user identity.

Use a combination of role-based access and overlay technologies to create a layered security approach

Q63. Refer to the exhibit.

After an initial setup of CX 8325 VSX configuration, the active gateway is set up for SVI 10. For testing purposes, SVI 10 on the sw-agg1 is shut down while traffic from the client connected to Edge-1 is initiated towards the default route.
What is the expected behavior while performing this test?

Traffic is potentially dropped between the client and the destination.

Traffic is forwarded over the ISL without the risk of dropped packets.

Traffic is unaffected and a 50ns failover time is expected for agg-sw2 to start traffic forwarding.

Traffic is dropped and vsx-sync will disable SVI10 on agg-sw2 automatically.

Q64. For enhanced port security in an HPE network, which two configurations can prevent unauthorized devices from gaining access?

802.1X with EAP-TLS

Static IP addresses

MAC-based authentication

IGMP Snooping

Q65. A pair of CX 8325 series switches a configured in a VSX cluster. Which function is executed on both VSX members during normal operation?

replies to ARP requests with thecluster vMAC

routes PIM and PIM-DR

relays DHCP requests or serves DHCP offer

periodically sends gratuitous ARP and broadcast hello packets

Q66. Aplying the command “ip Igmp snooping blocked VLAN 6. 6* on a port …

won’t prune multicast on that port on VLAN 5 and 6

won’t accept multicast Igmp joins on that port or VLAN 5 and 6.

won’t allow multicast traffic between VLAN 5 and 6.

won’t allow multicast on that port in VLAN 5 and 6 and disables the port.

Q67. Refer to the exhibit.

IGMP v3 was enabled on both VSX switches. Which switch becomes the IGMP querier forclients connected to Ace-1 switch?

Agg-2

both Agg-1 and Agg-2

Agg-1

Active gateway IP will be used as IGMP querier.

Q68. You are configuring an HPE Aruba Networking gateway cluster with AOS-10. What is true about gateway functionality? (Choose two.)

PAPI traffic is traversing through an IPSEC tunnel.

LACP is not supported when manually provisioning gateways.

Multiversioning between AP and gateways is not supported.

AOS-10 only supports high-value client session synchronization for the first failover.

User traffic in tunneled mode is encrypted per default.

Q69. A gateway cluster with AOS-10 is managed by HPE Aruba Networking Central. In a failover, what is the expected behavior of the client traffic?

Client traffic is disrupted during the AP bootstrap.

Client state synchronization is supported on each failover.

Client IPv4 multicast session failover is not supported.

Client state synchronization is supported on the first failover.

HPE7-A06 Exam Dumps – PDF Questions and Testing Engine: https://www.testkingit.com/HP/latest-HPE7-A06-exam-dumps.html

Pass HPE7-A06 Exam – Real Test Engine PDF with 128 Questions [Q53-Q69]

Leave a Reply Cancel reply