Sep-2024 Realistic JN0-664 Exam Dumps with Accurate & Updated Questions [Q17-Q31]

By adminOn September 12, 2024

Rate this post

Sep-2024 Realistic JN0-664 Exam Dumps with Accurate & Updated Questions

JN0-664 Exam Dumps – PDF Questions and Testing Engine

Q17. Exhibit

CE-1 must advertise ten subnets to PE-1 using BGP Once CE-1 starts advertising the subnets to PE-1, the BGP peering state changes to Active.
Referring to the CLI output shown in the exhibit, which statement is correct?

CE-1 is advertising its entire routing table.

CE-1 is configured with an incorrect peer AS

The prefix limit has been reached on PE-1

CE-1 is unreachable

Q18. Which two statements are correct about IS-IS interfaces? (Choose two.)

If a broadcast interface is in both L1 and L2, one combined hello message is sent for both levels.

If a point-to-point interface is in both L1 and L2, separate hello messages are sent for each level.

If a point-to-point interface is in both L1 and L2, one combined hello message is sent for both levels.

If a broadcast interface is in both L1 and L2, separate hello messages are sent for each level

Q19. Which two statements are correct about a sham link? (Choose two.)

It creates an OSPF multihop neighborship between two PE routers.

It creates a BGP multihop neighborship between two PE routers.

The PEs exchange Type 1 OSPF LSAs instead of Type 3 OSPF LSAs for the L3VPN routes

The PEs exchange Type 3 OSPF LSAs instead of Type 1 OSPF LSAs for the L3VPN routes.

Q20. Which two statements about the configuration shown in the exhibit are correct? (Choose two.)

This VPN connects customer sites that use the same AS number.

This VPN connects customer sites that use different AS numbers.

A Layer 3 VPN is configured.

A Layer 2 VPN is configured.

Q21. Your organization manages a Layer 3 VPN for multiple customers. To support advanced route filtering on your PE routers, you must advertise more than one BGP community on advertised VPN routes to remote PE routers.
Which routing-instance configuration parameter would support this requirement?

vrf-target import

vrf-export

vrf-target export

vrf-import

Q22. Exhibit

The environment is using BGP All devices are in the same AS with reachability redundancy Referring to the exhibit, which statement is correct?

RR1 is peered to Client2 and RR2

RR2 is in an OpenConfirm State until RR1 becomes unreachable.

Client1 is peered to Client2 and Client3.

Peering is dynamically discovered between all devices.

Q23. You are configuring a BGP signaled Layer 2 VPN across your MPLS enabled core network.
In this scenario, which statement is correct?

You must use the same route-distinguisher value on both PE devices.

You must assign a unique site number to each attached site’s configuration.

This type of VPN only supports Ethernet interfaces when connecting to CE devices.

This type of VPN requires the support of the inet-vpn NLRI on all core BGP devices.

Q24. Which two statements about IS-IS are correct? (Choose two.)

CSNPs are used to request a missing LSP.

PSNPs are used to acknowledge a received LSP.

PSNPs are used to request a missing LSP.

CSNPs are used to acknowledge a received LSP.

Q25. Exhibit

Referring to the exhibit, which statement is correct?

The vrf-target configuration will allow routes to be shared between CE-1 and CE-2.

The vrf-target configuration will stop routes from being shared between CE-1 and CE-2.

The route-distinguisher configuration will allow overlapping routes to be shared between CE-1 and CE-2.

The route-diatinguisher configuration will stop routes from being shared between CE-1 and CE-2.

Q26. Exhibit

You are attempting to summarize routes from the 203.0.113.128/25 IP block on R8 to AS 64500. You implement the export policy shown in the exhibit and all routes from the routing table stop being advertised.
In this scenario, which two steps would you take to summarize the route in BGP? (Choose two.)

Remove the from protocol bgp command from the export policy.

Add the set protocols bgp family inet unicast add-path command to allow additional routes to the RIB tables. –

Add the set routing-options static route 203.0.113.123/25 discard command.

Replace exact in the export policy with orlonger.

Q27. Exhibit

CE-1 and CE-2 are part of a VPLS called Customer1 No connectivity exists between CE-1 and CE-2. In the process of troubleshooting, you notice PE-1 is not learning any routes for this VPLS from PE-2, and PE-2 is not learning any routes for this VPLS from PE-1.

The route target must match on PE-1 and PE-2.

The route distinguisher must match on PE-1 and PE-2.

The instance type should be changed to I2vpn.

The no-tunnel-services statement should be deleted on both PEs.

Q28. Exhibit

Referring to the exhibit, you must provide Internet access for VPN-A using CE-1 as the hub CE.
Which two statements are correct in this situation? (Choose two.)

You must use RIB groups to leak routes between the inet. o and vpn-a. inet. o tables.

RIB groups are not needed to leak routes between the inet. 0 and VPN-A. inet. 0 tables,

Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> GW-1.

Internet traffic from Site 2 takes the path of PE-2 -> PE-1 -> CE-1 -> PE-1 -> GW-1.

Q29. You have an L2VPN connecting two CEs across a provider network that runs OSPF. You have OSPF configured on both CEs.
Which two statements are correct in this scenario? (Choose two.)

OSPF neighborship is formed between the CEs and PEs.

OSPF neighborship is formed between the two CEs.

The CE and PE OSPF areas must match.

The CE and PE OSPF areas can be different.

Q30. Which two statements are correct about VPLS tunnels? (Choose two.)

BGP-signaled VPLS tunnels require manual provisioning of sites.

LDP-signaled VPLS tunnels only support control bit 0.

LDP-signaled VPLS tunnels use auto-discovery to provision sites.

BGP-signaled VPLS tunnels can use either RSVP or LDP between the PE routers.

Q31. Referring to the exhibit, which statement is correct?

The vrf-target configuration will stop routes from being shared between CE-1 and CE-2.

The vrf-target configuration will allow routes to be shared between CE-1 and CE-2.

The route-distinguisher configuration will stop routes from being shared between CE-1 and CE-2.

The route-distinguisher configuration will allow overlapping routes to be shared between CE-1 and CE-2.

To be eligible for the Juniper JN0-664 certification exam, candidates must have a valid JNCIA-Junos certification or equivalent knowledge, and have at least one year of experience working with Juniper Networks service provider routing and switching technologies. Service Provider, Professional (JNCIP-SP) certification exam covers a wide range of topics, including advanced routing and switching technologies, MPLS, VPNs, QoS, and multicast protocols.

Juniper JN0-664 (Service Provider, Professional (JNCIP-SP)) Certification Exam is a professional-level certification exam that is designed for network engineers, administrators, and technicians who work in service provider environments. Service Provider, Professional (JNCIP-SP) certification exam is intended to test the knowledge, skills, and abilities of candidates who want to demonstrate their expertise in Juniper Networks service provider routing and switching technologies.

Pass Juniper JN0-664 Exam Quickly With TestKingIT: https://www.testkingit.com/Juniper/latest-JN0-664-exam-dumps.html

Sep-2024 Realistic JN0-664 Exam Dumps with Accurate & Updated Questions [Q17-Q31]

Leave a Reply Cancel reply