NEW QUESTION 21
Click the Exhibit button.

You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)

NEW QUESTION 22
Click the Exhibit button.

Your ONTAP cluster shows the cluster network errors that are shown in the event log. What is used by ONTAP software to log the errors that are shown in the exhibit?

NEW QUESTION 23
You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center.
In this scenario, what is the minimum number of spare disks required per node and disk type?

NEW QUESTION 24
You are planning to update your running switch environment. You must know that certain conditions exist before the FASTPATH software and the RCF on a NetApp CN1610 cluster switch can be installed.
Which condition must exist in this scenario?

NEW QUESTION 25
You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.
Which two actions should you perform before you turn over the cluster for production? (Choose two.)

NEW QUESTION 26
When you set up a new 2-node switchless cluster running ONTAP 9.5, which IP subnet is used for the automatic IP assignment on cluster ports?

NEW QUESTION 27
Click the Exhibit button.

A customer has a 2-node FAS8200 cluster with four DS212C shelves with 10 TB SATA drives.
Referring to the exhibit, an aggregate will be created with which default RAID type?

NEW QUESTION 28
According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?

NEW QUESTION 29
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)

NEW QUESTION 30
You are installing a new AFF A400 cluster for a customer. The customer indicates that they want to take advantage of AutoSupport On Demand.
In this scenario, which AutoSupport transport protocol must you use?

NEW QUESTION 31
You install a 4-node cluster with an AFF A400 HA pair and a FAS8300 HA pair. After setup, you are asked to review the audit logs on each controller from a Web browser.
In this scenario, which method provides access to the logs from a Web browser?

NEW QUESTION 32
You just installed two nodes into an existing ONTAP cluster.

When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.
Referring to the exhibit, which statement is true?

NEW QUESTION 33
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer’s requirement? (Choose two.)

NEW QUESTION 34
You are installing a new 2-node AFF A220 cluster running ONTAP 9.5. The customer would like to use the UTA2 adapters from the first controller to connect to the 10GbE front-end switches. On the second controller, they would like to use the first UTA2 port as a target FC port, and the second as an FC initiator. In this scenario, according to NetApp Best practices, what should your customer do?

NEW QUESTION 35
You installed a new pair of Cisco 92300YC cluster switches at a customer’s site. Before you install any files on the switch, you want to view the current configuration.
In this scenario, which command would you use to accomplish this task?

NEW QUESTION 36
Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.
In this scenario, which three resources would you use to find this information? (Choose three.)

NEW QUESTION 37
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer’s requirement? (Choose two.)

NEW QUESTION 38
You are planning the deployment of a new 8-node ONTAP 9.5 cluster. To prepare for the installation, you want to create a custom configuration worksheet with all the information that the customer provided. You also want to use the worksheet to generate CLI commands for your installation.
In this scenario, which NetApp tool will help you achieve your goal?

NEW QUESTION 39
Click the Exhibit button.

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.
Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

NEW QUESTION 40
Which hot-swappable transceiver is required to obtain full performance from a Cisco Nexus 3232C cluster-interconnect switch?

NEW QUESTION 41
Click the Exhibit button.

Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)

NEW QUESTION 42
You configured AutoSupport and are trying to send a full AutoSupport message to NetApp.
You use the autosupport history showcommand and see the output shown in the exhibit.

The customer confirms that the AutoSupport settings are correct.
Which two actions will solve this issue? (Choose two.)